(07-Sep-2016, 07:46 PM)mhd3000 Wrote: The frame  looks amazing , I wish if you make a copy fits 32*32 boards like beef

i wanted to, but it would make the frame 10mm wider and longer...
These FC's are becoming outdated
time to get the smaller boards

Hi,

I'm having issue with my EVO F3 brushed board,
I have connected all 4 motors to CleanFlight configurator, went to Motors section-> Motor test ->
Try to run each motor but nothing happens
Did I miss something obvious or all FET's on that board are faulty ?

(11-Sep-2016, 09:31 PM)pakamon Wrote: Hi,

I'm having issue with my EVO F3 brushed board,
I have connected all 4 motors to CleanFlight configurator, went to Motors section-> Motor test ->
Try to run each motor but nothing happens
Did I miss something obvious or all FET's on that board are faulty ?

battery connected?
does it work when you arm?

Battery not connected while Cleanflight configurator hooked up.
Tested also armed (throttle bottom right) without any difference
Please correct me if I'm wrong but Motor test in Cleanflight should work with or without arming right?

Hello i have received a Bg f3 brushed fc after a month of shipping but i am having some problems connecting to cleanflight.
I downloaded every driver for windows and rebooted pc.the pc recognize it as stm32 device but in cleanflight after 10 seconds timed out and failed connecting but Com 1 port seems ok since it opens and close correctly.
This board comes already flashed from banggood?
What is wrong? Manual port or Bauds? Faulty board?

(20-Sep-2016, 07:55 AM)lorentz Wrote: Hello i have received a Bg f3 brushed fc after a month of shipping but i am having some problems connecting to cleanflight.
I downloaded every driver for windows and rebooted pc.the pc recognize it as stm32 device but in cleanflight after 10 seconds timed out and failed connecting but Com 1 port seems ok since it opens and close correctly.
This board comes already flashed from banggood?
What is wrong? Manual port or Bauds? Faulty board?

It worked out of the box for me without installing any dirvers..
can you see other COM port after connecting? baud rate should be the same as other FC's.
can you re-flash firmware? (look up how to flash EVO F3 board if you are not sure)

if still not luck it's probably a bad board.

(20-Sep-2016, 01:15 PM)Oscar Wrote: It worked out of the box for me without installing any dirvers..
can you see other COM port after connecting? baud rate should be the same as other FC's.
can you re-flash firmware? (look up how to flash EVO F3 board if you are not sure)
if still not luck it's probably a bad board.

thanks Oscar. No when plugged i can see only com 1 on cleanflight...may i have to manual choose the port?

(20-Sep-2016, 02:11 PM)lorentz Wrote: thanks Oscar. No when plugged i can see only com 1 on cleanflight...may i have to manual choose the port?

when you unplug the FC, is com1 still there? The manual for choosing port is, whichever port appears when you plugin the board, that's the port
if no new port appear when you plug FC in, it probably means you haven't installed the correct driver yet.

Reflashed correctly using zadig (now with dfu option in cleanflight) but still unable to connect....
After flashing it rebooted but now it has always the solid red led and no more blue led flashing.

---

Tried to short again the boot pads but nothing changed...still only the solid red led

---

And the blinking blue led is on after the successful flashing but when reconnected to usb the blue led goes off and remain online solid red only

(20-Sep-2016, 06:14 PM)Oscar Wrote: when you unplug the FC, is com1 still there? The manual for choosing port is, whichever port appears when you plugin the board, that's the port
if no new port appear when you plug FC in, it probably means you haven't installed the correct driver yet.

Thx Oscar.it has always showed com1 port also when unplugged.
i have installed every driver listed in cleanflight,Stm included.tried also manual connect but the default dont works.Tried to copy and paste the location form the device manager of win7 without risult.
After installation of st drivers my pc see the fc ad stm32 but in cleanflight nothing...i am going insane.
Ps
The first time i plugged the fc it has solid red and blinking blue led

Anyone experienced the same issues?

(22-Sep-2016, 12:26 PM)lorentz Wrote: Anyone experienced the same issues?

Not with this board, but I once had an issue with a bad USB cable.  Got another one to try?

(21-Sep-2016, 03:59 PM)lorentz Wrote: Thx Oscar.it has always showed com1 port also when unplugged.
i have installed every driver listed in cleanflight,Stm included.tried also manual connect but the default dont works.Tried to copy and paste the location form the device manager of win7 without risult.
After installation of st drivers my pc see the fc ad stm32 but in cleanflight nothing...i am going insane.
Ps
The first time i plugged the fc it has solid red and blinking blue led

sorry i have run out of idea.. i think it's just a bad board. Your computer works with other cleanflight FC right?

(22-Sep-2016, 01:21 PM)Oscar Wrote: sorry i have run out of idea.. i think it's just a bad board. Your computer works with other cleanflight FC right?

Thx anyway Oscar. No the other fc i use run on librepilot..tried also to reinstall cleanflight.
Faulty board i suppose.

Hi. Solved the issue. .was a wrong usb driver.
Now it works but when armed with aux 1the motors are spinning all at mid throttle.
Set pwm 32000,low 1000, mid 1500, Max 2000.
Any idea?
Thanks