Hello
I've bought QWinOut LS-800D FPV Goggles 5.8G 40CH (https://qwinout.com/products/qwinout-ls-...odel-racer) and I would like to use wth my Mobula 6hd (HAMO/CRAZYBEEF4FR(STM32F411))
I have setup following
# vtxtable

vtxtable bands 5

vtxtable channels 8

vtxtable band 1 BOSCAM_A A CUSTOM  5865 5845 5825 5805 5785 5765 5745 5725

vtxtable band 2 BOSCAM_B B CUSTOM  5733 5752 5771 5790 5809 5828 5847 5866

vtxtable band 3 BOSCAM_E E CUSTOM  5705 5685 5665    0 5885 5905    0    0

vtxtable band 4 FATSHARK F CUSTOM  5740 5760 5780 5800 5820 5840 5860 5880

vtxtable band 5 RACEBAND R CUSTOM  5658 5695 5732 5769 5806 5843 5880 5917

vtxtable powerlevels 3

vtxtable powervalues 0 1 2

vtxtable powerlabels 25 100 200



# vtx

vtx 0 0 0 0 0 900 900

vtx 1 0 0 0 0 900 900

vtx 2 0 0 0 0 900 900

vtx 3 0 0 0 0 900 900

vtx 4 0 0 0 0 900 900

vtx 5 0 0 0 0 900 900

vtx 6 0 0 0 0 900 900

vtx 7 0 0 0 0 900 900

vtx 8 0 0 0 0 900 900
vtx 9 0 0 0 0 900 900

But I don't see any image.
Any suggestions please?

Ciao
Cosma

I think the default channel Happymodel uses is R1 (5658). Try and tune your goggles to R1.

If not then connect your quad to Betaflight Configurator and in the VTX tab check what Frequency/Band/Channel is currently set.

No sorry also R1 5658 doesn't run :-(
I setup goggles and Mobula

any configuration file already ready for Mobula 6 and QWinOut LS-800D ?
Thanks

If you power up the Mobula6 HD and connect it to the Betaflight Configurator and go to the VTX tab, does it say Device ready?

Paste your full CLI dump here so we can see your complete setup.

(01-Aug-2022, 12:06 AM)kafie1980 Wrote: If you power up the Mobula6 HD and connect it to the Betaflight Configurator and go to the VTX tab, does it say Device ready?

Paste your full CLI dump here so we can see your complete setup.

Hello 
configuration seems to be fine and VTX tab says Device Ready YES
I attach screenshots and CLI Dump
Thanks a lot

Your vtx is on channel E1.

Are your goggles set for E1 as well?

(01-Aug-2022, 02:21 PM)kafie1980 Wrote: Your vtx is on channel E1.

Are your goggles set for E1 as well?

Hello yes I set manually on E-1 and also I tried auto-scan

Do you have another quad to test?

Either there is an issue with the VTX on the Mobula 6 AIO board which can burn out if left powered on the desk for excessive periods without active cooling.

Or there is an issue with the VRX module in the goggles.

(02-Aug-2022, 01:28 AM)kafie1980 Wrote: Do you have another quad to test?

Either there is an issue with the VTX on the Mobula 6 AIO board which can burn out if left powered on the desk for excessive periods without active cooling.

Or there is an issue with the VRX module in the goggles.

I've ordered another Mobula 6 board and as soon as I get I will check, I've also requested a substitution of the goggles
Thanks a lot
Cosma

Dear all
I've replaced the main board of the drone and now it runs well. Probably the Mobula 6 AIO board was defective.
I can see the video on QWinOut LS-800D FPV Goggles 5.8G 40CH
Thanks a lot for support
Cosma