Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 20-Apr-2019, 06:42 AM (This post was last modified: 20-Apr-2019, 06:51 AM by mza81.) I've connected the yellow wire to TX1 and still nothing. only telemetry works. then i remove the sbus out wire and still o ly telemetry works.
TX3 and TX6 shares the same UART. can TX3 still be used?
I have just check my voltage out from SBUS out (RX) to SBUS (FC) is 0.55V. Is this normal?
• Posts: 12,098
Threads: 125
Likes Received: 3,739 in 2,836 posts
Likes Given: 99
Joined: Feb 2017
Reputation:
388 If you have a bridge, yes you need to solder. And still believe the serial rx is on UART6. And TX3 and TX6 do not share an UART.
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 i have no idea what a bridge is for. I guess i leave it alone first.
yes i set the serial RX to UART6. UART 1 is my smart port. UART3 is disabled.
Currently the yellow cable is at TX1.
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 Bridge done. Whats next...
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 My telemetry is going bogus...sometimes it detect. and then sometime a few went missing. sigh...
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 20-Apr-2019, 08:34 AM (This post was last modified: 20-Apr-2019, 08:46 AM by mza81.) done.
how about the yellow cable?
anyway, its all the while been like that.
I have change from TX1 to TX3 and now my telemetry stabilize.
Did the programming
feature -softserial
set serialrx_provider = sbus
set serialrx_inverted = off
and saved.......still no improvement
smartport is at UART 3
serial rx is at UART 6
• Posts: 12,098
Threads: 125
Likes Received: 3,739 in 2,836 posts
Likes Given: 99
Joined: Feb 2017
Reputation:
388 try changing serial rx to uart1
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 OMG!!! Like FINALLY! Tears of joy running down my cheeks right now....
It's finally ALIVE!
Thank you so much Voodoo....Must be a pain to guide a noob like me..
• Posts: 12,098
Threads: 125
Likes Received: 3,739 in 2,836 posts
Likes Given: 99
Joined: Feb 2017
Reputation:
388 I hate Omnibus for having some many version. It so hard to help because it is hard to tell which board you have and which port the SBUS pin isl linked to. Anyway, glad it worked.
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 Yikes...then which FC will you recommend to buy next?
Anyway, after this, what should I do?? I dont think its ready to fly right??
• Posts: 17
Threads: 0
Likes Received: 0 in 0 posts
Likes Given: 0
Joined: Apr 2019
Reputation:
0 21-Apr-2019, 06:32 AM (This post was last modified: 21-Apr-2019, 06:39 AM by mza81.) I just realize my Yaw and throttle is moving together. when i move my left stick, up and down, both yaw and throttle moves. But when i move my left stick, left and right, nothing happens.
Updated - My QX7 Inputs had 2 throttles. Already did the changes and now looks ok. This drone building is sucking my brain juice dry. LOL.
•