I need pid for  iflight portek 35 hd
Thank you if you send it to me

You can find all the factory CLI dumps (which includes the factory PIDs) for the iFlight ProTek35 at the following link...

https://drive.google.com/drive/u/0/mobil...irection=a

Thank you

How can I distinguish the bm270 version with the MPU600?

(26-Sep-2022, 10:24 PM)rezafpv Wrote: How can I distinguish the bm270 version with the MPU600?

The easiest way to find out what gyro your FC has is to connect Betaflight Configurator to the FC and run the "status" command in the CLI. That will tell you what type of gyro is on the FC. One of the lines will begin with "GYRO=" with the gyro type listed next to it.

Thank you
Thank you for your guide

I had a problem
The firmware version of the dump file was 4.2.9 and I downgraded the firmware to this version
But after I got this version 4.2.9, my barometer stopped working
Although the barometer item is active, it does not work
where is the problem from ?

Please can you run the "status" command in the CLI and post the results back here.

Please also run the "dump" and "resource show all" commands in the CLI and post the results of those back here as well.

I think the barometer works from version 4.3 onwards

(27-Sep-2022, 01:42 AM)SnowLeopardFPV Wrote: Please can you run the "status" command in the CLI and post the results back here.

Please also run the "dump" and "resource show all" commands in the CLI and post the results of those back here as well.

# status
MCU F745 Clock=216MHz, Vref=3.29V, Core temp=41degC
Stack size: 2048, Stack address: 0x20010000
Config size: 3986, Max available config: 32768
Gyros detected: gyro 1
GYRO=MPU6000, ACC=MPU6000
OSD: MAX7456
System Uptime: 44 seconds, Current Time: 2022-09-27T07:32:20.022+00:00
CPU:2%, cycle time: 125, GYRO rate: 8000, RX rate: 33, System rate: 9
Voltage: 59 * 0.01V (0S battery - NOT PRESENT)
I2C Errors: 3
SD card: Not configured
Arming disable flags: RXLOSS CLI MSP

(27-Sep-2022, 01:42 AM)SnowLeopardFPV Wrote: Please can you run the "status" command in the CLI and post the results back here.

Please also run the "dump" and "resource show all" commands in the CLI and post the results of those back here as well.

resource show all Attachment

The new versions of the iFlight Beast F7 V2 AIO FC has a DPS310 barometer on it which isn't supported by Betaflight 4.2.x or earlier. iFlight have created custom Betaflight 4.2.11 hex firmware for some of their other flight controllers that now have the DPS310 barometer (instead of a BMP280 barometer) but unfortunately they don't appear to have done that for the iFlight Beast F7 V2 AIO FC.

You have one of the following two options:

1. Reach out to iFlight support (from HERE) and ask them where you can get a custom Betaflight 4.2.11 hex file for the iFlight Beast F7 V2 AIO FC that has support for the DPS310 barometer. Note that you can apply the factory 4.2.9 CLI dump to a 4.2.11 firmware installation with no issues.
   
2. Flash Betaflight 4.3.1 to your FC (which does support the DPS310 barometer) and then configure / tune the quad yourself from scratch.
   

Thank you very much for your advice
I contacted iflight and they are creating a file for me
I will let you know the result after preparation

If you do manage to get hold of a custom Betaflight 4.2.11 firmware hex file from iFlight for the iFlight Beast F7 V2 AIO FC which supports the DPS310 barometer, can you please upload it here for others who may be looking for the same in future. The forum doesn't accept file attachments with a ".hex" extension so you will need to zip it up and then upload the ZIP file containing the hex file.