I had some issue with OSD configuration, vtx table and UART for the Rx

[Rosssiiii]

@Snowleopard

Hello
https://intofpv.com/t-issues-in-fw-upgra...#pid150134

I'm considering the old theared where I have already did the Fw update on that specific fc

GEPRCF405

So considering that I have did the update from bf 4.2.9 to 4.2.11 is efficient restore the diff file, but in that case because I saw some strange things with the old fw maybe is better if I put the values manually from GUI or could upload the old diff all ?

even if restore the diff and if the diff is formally correct there shouldn't be issues.

But I wait for a confirm, personally I would feel a bit more safe doing it manually from gui

PORTS:
https://i.imgur.com/hGzS58r.png
the system alredy understand that i have the rx on the uart6 , so i don't have to change anything right ?

on the UART5 what is indicated as active ?

does i need to able just the GPS on the UART 1 righ ?

For the vtx table i have the old file BTFL_vtxtable_Wizard_x220_v2_20210817_180450.json
that contain it:

{
    "description": "Betaflight VTX Config file",
    "version": "1.0",
    "vtx_table": {
        "bands_list": [
            {
                "name": "BOSCAM_A",
                "letter": "A",
                "is_factory_band": true,
                "frequencies": [
                    5865,
                    5845,
                    5825,
                    5805,
                    5785,
                    5765,
                    5745,
                    5725
                ]
            },
            {
                "name": "BOSCAM_B",
                "letter": "B",
                "is_factory_band": true,
                "frequencies": [
                    5733,
                    5752,
                    5771,
                    5790,
                    5809,
                    5828,
                    5847,
                    5866
                ]
            },
            {
                "name": "BOSCAM_E",
                "letter": "E",
                "is_factory_band": true,
                "frequencies": [
                    5705,
                    5685,
                    5665,
                    5645,
                    5885,
                    5905,
                    5925,
                    5945
                ]
            },
            {
                "name": "FATSHARK",
                "letter": "F",
                "is_factory_band": true,
                "frequencies": [
                    5740,
                    5760,
                    5780,
                    5800,
                    5820,
                    5840,
                    5860,
                    5880
                ]
            },
            {
                "name": "RACEBAND",
                "letter": "R",
                "is_factory_band": true,
                "frequencies": [
                    5658,
                    5695,
                    5732,
                    5769,
                    5806,
                    5843,
                    5880,
                    5917
                ]
            }
        ],
        "powerlevels_list": [
            {
                "value": 0,
                "label": "25 "
            },
            {
                "value": 1,
                "label": "200"
            },
            {
                "value": 2,
                "label": "400"
            },
            {
                "value": 3,
                "label": "600"
            }
        ]
    }
}

CONFIGURATION:
https://i.imgur.com/QdY71up.png
https://i.imgur.com/GeEUKm0.png
https://i.imgur.com/WhchDVs.png

RECEIVER:
https://i.imgur.com/V3RRu9Y.png

MODES:
https://i.imgur.com/K6sKPRG.png

But inside the diff there anrent't the configuration about modes and port, i was looking for it?