Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
ZMR250 build spinning uncontrollably
#16
(13-Apr-2016, 06:04 AM)kandelin16 Wrote: Well crap. You're right.
Sorry guys! Please excuse my ignorance. I'll let you know how things go after I re-solder everything.
And thank you very much to everybody!

lol, i had this on one of my quad  once , it took me awhile to figure it out   Wink .   it's when things go wrong you start to learn , good luck bud .
Reply
Login to remove this ad | Register Here
#17
(13-Apr-2016, 08:41 PM)Trollhammered Wrote: It's probably to late to say but you can change the motor direction in BLHeli suite

Really? I never looked! now I feel ignorant! Going to do this next time instead of switching leads!
I am a developing Racer - getting better.....
BNF Quads: <250 Eachine>; <250 Walkera Advanced CC3D>; <250 Vortex Pro>
Built: Dronz Fury 252 RX ; Speed Addict 210-R
Building: <Deciding on Third build - Suggestions?>
Reply
#18
(13-Apr-2016, 08:41 PM)Trollhammered Wrote: It's probably to late to say but you can change the motor direction in BLHeli suite

That is IF he is using blheli.
That happened to me once when I flashed my 9x from stock to openTX. My issue was that I had mapped the wrong channels on the tx an yaw had a constant input from a switch.
Reply
#19
Can we assume that you have also calibrated your ESCs?
When you calibrate your ESCs, and in CleanFlight through the motors tab, if you control each motor individually, do they all "sound" the same when you rev. them up? I've had ESCs that calibrate, but don't spin to the same speed as the others. That caused an issue for me similar to yours. Once I changed out the ESC it ran fine.

Don't know what others see, I see about a 25% failure rate of new ESCs. BUT, I've only used DYS SN20A ESC so far (~16). I really like them other than the failure rate. I should note that some of the 25% I have managed to repair. Most times just touching up the solder connections takes care of the issue.
Reply
#20
(13-Apr-2016, 08:41 PM)Trollhammered Wrote: It's probably to late to say but you can change the motor direction in BLHeli suite

So my ZMR has spent the last couple months as a autonomous hovercraft for an engineering class. Now that im done Im ready to start working on this again! can this be done for simonk escs as well?
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  First Build - prevent antenna chop? JohnnyCornRocket 5 127 8 hours ago
Last Post: iFly4rotors
  Best Battery Option for Build - Begginer Arkadius27 7 151 19-Mar-2024, 04:40 PM
Last Post: Pathfinder075
Sad What to check for short in a build? Yesnok 1 108 03-Mar-2024, 12:06 PM
Last Post: iFly4rotors
  First Build Critique Crashesintotrees 3 163 01-Mar-2024, 04:25 PM
Last Post: Pathfinder075
  My first build and a few concerns bozon 15 461 21-Feb-2024, 01:44 PM
Last Post: bozon


Login to remove this ad | Register Here