Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Quadcopter build motor spinning like 1/2 rotation per seconds. Help!
#1
Hello,
I built a quadcopter last year around august and it went offline till today. I have literally forgot almost everything concerning quads and trying to catch up.
My problem is that when i turn the quad on and did a calibration with the transmitter, then pushing the throttle up after the third motor is spinning like 1/2 a rotation per seconds then back going to its original location. Any help will be greatly appreciated.
Here's the specs: (all purchases were from ebay)
Transmitter:  Fly Sky FS-T6
Receiver: Fly Sky FS-R6B
Motors: No Name written on it just: A2212-KV1000 4 like these [Image: rofl.png]
ESCs: Hobby Fans ESC-30A
Flight Controller:[Image: rofl.png] Nothing written on it [Image: biggrin.png] but the got some info that might be useful: HW ver: 2.1.X
                                                                                                                               FW ver: 1.19S1 Pro
                                                                                                                               Steveis
Batter: Black Magic 25C-3000mAh
Reply
Login to remove this ad | Register Here
#2
Your controller is a KK2.1.(5 probably). Aaron on this forum has some experience. I have one, but I've also forgotten all I knew about it Big Grin . I'm guessing your quad is a 450 (or larger) size. Not clear on the motor behavior - got a short video or something? (Might be a crappy solder joint on motor to esc.)

If the motors have plugs, easy to swap motors around and see if the behavior follows the motor or stays on the same arm. (Check rotation direction if you do that.)
Reply
#3
If just 1 motor is behaving weirdly, it's likely to be the ESC/motor having cold solder joints, or motor screws are too long touching motor wilding.
Don't be a LOS'er, be an FPV'er :)  My Gear - Facebook - Instagram - Twitter
Reply
#4
will try to re-solder the joints and give a feedback
Yes it is 450
Edit: i don't think its a screw holding the inside of the motore cause i was flying fine last year.
I will disassemble everything and re assemble it since it is messy and ugly build.
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  First Build - prevent antenna chop? JohnnyCornRocket 5 127 Yesterday, 02:16 PM
Last Post: iFly4rotors
  4 inch frame with 16x16 motor mounting holes Pathfinder075 10 169 19-Mar-2024, 07:02 PM
Last Post: Pathfinder075
  Best Battery Option for Build - Begginer Arkadius27 7 151 19-Mar-2024, 04:40 PM
Last Post: Pathfinder075
Question 3'' FPV Quadcopter samysh 19 655 09-Mar-2024, 11:37 PM
Last Post: Pathfinder075
Sad What to check for short in a build? Yesnok 1 108 03-Mar-2024, 12:06 PM
Last Post: iFly4rotors


Login to remove this ad | Register Here