Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Naze32 rev6 beep codes on power
#1
Lately when my naze32 rev6 is powers on the buzzer gives off 3 fast beeps and 2 slow beeps. Here is my video.

Has anyone seen this before?

While it is beeping like this I can't connect to it via betaflight.
Does it with either battery or USB power
I have the accelerometer off
Reply
Login to remove this ad | Register Here
#2
I have two quads the use the same board.  Mine acts the same way when it powers up but with but the beeps are probably three times as long with longer intervals in-between.  On mine, the three consecutive beeps are the gyros calibrating.  Not sure what is going on with yours...error code maybe? Thinking
"Damn the torpedoes!!!  Full speed ahead!!!"
Reply
#3
Sounds like an error code most probably associated with a dead gyro/gyro not found. I had the same on my rev5 I got from multirotorparts and they confirmed it's a hardware issue and sent me a new one. I was able to flash sometimes, but not connect to gui.

You can try a solder reflow on gyro chip if you want to save this board, I've read it sometimes solves the issue. I just trashed mine.
Find me on Youtube and Instagram. I currently fly: DRC Aura, NOX5R, Minimalist 112 and drive a scrap RC car
Reply
#4
or you can reuse it as part of an intro to darude sandstorm Smile

question - was it flying before or it is a fresh build? if fresh have you connected the board before soldering stuff on it?
All the best
Grzesiek (Grisha/ Greg)

Curently flyable: Nox 5, Minimalist 112
Bench / in progres: fixing Nox 3,  Scrap
thinking about building: 450


Reply
#5
It is not a fresh build. The beeping eventually stops and it reboots and everything is fine. I feel like the gyro may be going bad. Just going to bite the bullet and buy a Motolabs Cyclone.
Reply
#6
in that case i would order new board and replace it... as this will eventually fail in the crucial moment (electronics is known to break in the worst possible moment)

as you describe it looks lie gyro is starting starting starting... eventually kicks in... question when will it stop ?
All the best
Grzesiek (Grisha/ Greg)

Curently flyable: Nox 5, Minimalist 112
Bench / in progres: fixing Nox 3,  Scrap
thinking about building: 450


Reply
#7
(27-Oct-2016, 10:23 AM)Grisha0 Wrote: in that case i would order new board and replace it... as this will eventually fail in the crucial moment (electronics is known to break in the worst possible moment)

as you describe it looks lie gyro is starting starting starting... eventually kicks in... question when will it stop ?

It stops after about 8-10 seconds.  When it does, you hear the FC startup.
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Build What motors for 4" power quad? romangpro 30 2,178 21-Sep-2023, 02:26 AM
Last Post: romangpro
  SpeedyBee F7 V3 Power Issues SoFarKingFast 8 686 13-Jun-2023, 09:54 PM
Last Post: Pennywise
  Help 3" video noise only when armed and only if Unify Pro32 Nano power 400mW+ udy 6 2,055 09-May-2022, 03:26 AM
Last Post: Rob3ddd
  Help Issue with power? ropilofski 14 2,418 03-Oct-2018, 06:33 PM
Last Post: ropilofski
  Help zmr250 Build - Cannot Arm naze32 relentlessly 7 3,039 13-Jul-2016, 02:10 PM
Last Post: JimmyLe813


Login to remove this ad | Register Here