Hey guys, yesterday my FC went out in smoke after some rewiring and I found this while searching for a replacement.
It ticks all my boxes so I'll probably get one to replace the dead RaceBase.
What I find most interesting is:
- F4 and MPU6000
- Integrated OSD and filtered 12v for FPV gear
- Stackable PDB with current sensor (included), low profile and no wires required
- Handles 5S
- Extra UARTs
- SD card slot
Details
KIWI is a powerful STM32F4 CPU based flight controller, fast, reliability and full of awesomeness. Using low noise MPU6000 gyro on SPI bus for faster acquisition of gyro data. Board have 3 fully usable UART ports without interference in USB port (VCP) compatible with BLHELI passtrough, SDCard slot, 5V up to 5S step-down and 12V linear BEC. All this things are complemented by OSD customizable directly with Betaflight Configurator.
Specification
STM32F405 processor, 170MHz
low noise, vibration resistant MPU6000 gyro chip on SPI-bus
compatible with latest Betaflight releases also can be used with Raceflight (at this time without OSD function)
switching step-down 5V and 600mA current output, up to 6S input (not needed external 5V regulator)
12V/0.7A linear BEC for video line
LC filter on video line
SDCard slot for data logging
OSD (only for betaflight)
USB port independent of UART ports
programmable, hardware SBUS inverter
dedicated Spektrum Satellite connector with 3.3V output
buzzer driver
LED strip output
VBAT monitor
RSSI monitor
current monitor
BOOT button for simple flashing
DSHOT600 support
dedicated PDB with current sensor up to 160A (included!)
Firmware
From Betaflight version 3.1 and above FW will be available direct from configurator. Version 3.1.6 is available to download on bottom of this page.
Available here: https://flyinglemon.eu/flight-controller...oller.html
EDIT: Updated with info and pictures about v2
EDIT2: Add attachment with wiring diagram
It ticks all my boxes so I'll probably get one to replace the dead RaceBase.
What I find most interesting is:
- F4 and MPU6000
- Integrated OSD and filtered 12v for FPV gear
- Stackable PDB with current sensor (included), low profile and no wires required
- Handles 5S
- Extra UARTs
- SD card slot
Details
KIWI is a powerful STM32F4 CPU based flight controller, fast, reliability and full of awesomeness. Using low noise MPU6000 gyro on SPI bus for faster acquisition of gyro data. Board have 3 fully usable UART ports without interference in USB port (VCP) compatible with BLHELI passtrough, SDCard slot, 5V up to 5S step-down and 12V linear BEC. All this things are complemented by OSD customizable directly with Betaflight Configurator.
Specification
STM32F405 processor, 170MHz
low noise, vibration resistant MPU6000 gyro chip on SPI-bus
compatible with latest Betaflight releases also can be used with Raceflight (at this time without OSD function)
switching step-down 5V and 600mA current output, up to 6S input (not needed external 5V regulator)
12V/0.7A linear BEC for video line
LC filter on video line
SDCard slot for data logging
OSD (only for betaflight)
USB port independent of UART ports
programmable, hardware SBUS inverter
dedicated Spektrum Satellite connector with 3.3V output
buzzer driver
LED strip output
VBAT monitor
RSSI monitor
current monitor
BOOT button for simple flashing
DSHOT600 support
dedicated PDB with current sensor up to 160A (included!)
Firmware
From Betaflight version 3.1 and above FW will be available direct from configurator. Version 3.1.6 is available to download on bottom of this page.
Available here: https://flyinglemon.eu/flight-controller...oller.html
EDIT: Updated with info and pictures about v2
EDIT2: Add attachment with wiring diagram