Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Im stumped - Noisy Yaw on Gyro.
#1
Hi Guys, I've been working on this issue the past 3 days.

I'm getting tiny twitches on my yaw (especially when hovering) that shows up on my recorded footage on a Hero 4 

I've done the following:
  • Soft mounted the FC with the use of rubber o-rings.
  • Adjusted the notch filter. (attachments show before notch filter was adjusted.)
  • Adjusted PID's
  • Checked my motors for any vibrations.
It seems to be gyro noise from what I can see.  Any idea what else I can try or what im doing wrong.

My Quad:

Frame:  DALRC XR215
FC:  SP Racing F3 6dof  - (MPU 6050)
FIRMWARE:  Betaflight 3.0 - 4khz & 4khz.
ESCS:  DYS XS 30A - Multishot.
MOTORS:  Emax RS2205 2300kv.
PROPS:  HQ Prop 5040x3 Skitzo Edition.

Pids / Filter
       

Blackbox - Yaw P gain + Gyro. (after adjusting notch filter)  / All Gyros.
       

Notch Filters (before change)

Roll / Pitch / Yaw
           

Much Appreciated, Venom.
Reply
Login to remove this ad | Register Here
#2
You did not mention your power train. Did you mount low-esr capacitors on escs or pdb? If not, could be electrical noise.

But the roll noise (before notch) is also pretty strong. Does it look ok after the filter?
Reply
#3
when you mount your FC do the screws go in easy? or do they rub against the mounting holes of the board? if they are to tight then that would make the O rings useless. if that's the case then drill or make the holes a little bigger so it sits freely on the screws.
Reply
#4
Could that be your camera mounting?
One time I was troubleshooting my tuning, because I got this vibration in my footage, many days later I realized it was my sloppy gopro camera mount!
Don't be a LOS'er, be an FPV'er :)  My Gear - Facebook - Instagram - Twitter
[-] The following 2 users Like Oscar's post:
  • E.L.K., Tom BD Bad
Reply
#5
(14-Jan-2017, 08:43 AM)Oscar Wrote: many days later I realized it was my sloppy gopro camera mount!

this is human nature expecting the worst! My sister in law just spent about $150 on diagnosing a blown fuse in her car!
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  random uncommanded yaw issue in flight? husafreak 30 836 16-Jan-2024, 05:32 AM
Last Post: husafreak
  Build T-Motor F7 stack - Betaflight Gyro update frequency 3.2kHz ???? MindBenderFPV 2 3,019 18-Jun-2022, 09:10 AM
Last Post: SnowLeopardFPV
  Matek AIO FC yaw twitch issue TomP7715 5 1,199 22-Sep-2018, 10:51 PM
Last Post: Fisherking
  Help No pitch, roll or yaw commands working DannyZ 2 1,248 21-Jun-2018, 07:23 PM
Last Post: Drone0fPrey
  using head tracker for yaw? JimmyLe813 5 1,466 21-Mar-2017, 12:21 PM
Last Post: campagnium


Login to remove this ad | Register Here