If you enjoy our forum, why not join us? :) Login removes all the ads too! Click here to register in a few simple steps

Login to remove this ad | Register Here
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How to Lubricate brushless Motors - mini quad Quadcopters RC
#1


In a brushless outrunner motor, the parts that generate friction is the shaft bearings. After some usage it might get dry and start making noise, lubricant can help improving the smoothness and efficiency.

Here Alex showed us how he lubricate his cobra brushless motors for his mini quadcopter.

Check out his tutorials
http://blog.alexyorke.net/lubricate-brus...-bearings/



Lubricating your motor bearings is an important part of motor maintenance and in the long run can lead to extended life. more flying == greater happiness Smile

Choosing the right oil/lubricant

Choosing the correct oil to use for your motors can be tricky if you don’t know what to look out for. You want to find an oil/lubricant that can handle parts moving at a high RPM, heavy-duty, high temperatures and humid environments. Knowing all of this you MUST NOT USE WD-40.

WD-40 is possibly one of the worst things you can put on your motor bearings. It is fantastic for applications such as freeing up hinges, locks, cleaning and rust-prevention but it is not marketed or sold as a lubricant.  lubricants must have good oxidation resistance to resist sludge build up at operating temperatures (in our case, this can be quite high) and most lubricants are formulated with antioxidant additives to provide this protection. However, WD40 does not contain such additives and would likely degrade to form sludge fairly rapidly.

A good choice of lubricant would be one that is specifically designed for the lubrication of high speed parts at higher temperatures. I’ve found that one of the best choices for this is Singer Super Oil which is a good cheap universal lubricant.

Singer super oil

This oil is specially formulated for lubricating sewing machines which have a lot of small fast moving parts that generate a lot of friction and heat. This oil is perfect for our application and can be found online for around $5 (£3) for 125ml.

Another alternative oil is the Tarot High-Speed Bearing Oil that can be found on banggood for about £7 (£5).

What parts to lubricate

Within the typical brush-less motor designed for use on a quadcopter, you will typically have 2 bearings. See below at the stator of a DYS 1806 and cobra 2204 motor, one bearing is on the top of the stator, and the other is on the bottom.

Top bearing on motor stator (Left is cobra 2204, right is DYS 1806).

Top bearing on stator

Bottom bearing on motor stator:

Bottom bearing on stator

These types of bearings are called shielded bearings and are designed to keep the majority of the grime and rubbish out of the bearing enclosure, unlike sealed bearings which are used on higher quality motors and keep everything out of the bearing enclosure.

Method

I tend to lubricate my motor bearings each week after heavy use, its best to do this after cleaning all the dirt off and out of your motors (crashing is a big part of 250 flying!) and I’ve discovered a little trick that I’ve found works really well.

Hypodermic Needle

You will need to get hold of a hypodermic syringe and rounded needle (or any needle, I prefer to not have sharp things with oil in them lying around on my desk!) for the application of the oil. You don’t need too much, just a few drops on each bearing and then spin the motors to make sure the application is even. Once done, I leave them for the night until I’m ready to fly again the next day! simple right?

How to reach inside motor



You can pick up a pack of hypodermic syringe and needles on ebay for a few $ Smile http://www.ebay.co.uk/itm/231080683351
Don't be a LOS'er, be an FPV'er :) -- Blog - Facebook - Instagram - Twitter - Google Plus
#2
Hi Oscar, that link you posted is broken,
Reply
#3
I use a small syringe with fine tipped needle and apply singer sewing machine oil to my bearings. Has worked really well , generally now when the bearing does get a bit too noisy I just ditch the motor and buy a new one. (which does not happen too often..I normally break the motor before a bearing fails..lol)

Too much time and effort to replace a bearing and maybe a shaft and c-clip. Just lube your bearings, Clean out your motors in the field with a can of compressed air.
Reply
Login to remove this ad | Register Here
#4
(05-Feb-2016, 04:59 AM)quadfish Wrote: Hi Oscar, that link you posted is broken,

yea... Alex's site is down...
Don't be a LOS'er, be an FPV'er :) -- Blog - Facebook - Instagram - Twitter - Google Plus
Reply
#5
Hey Oscar your image isn't working, not sure if thats because it was uploaded and the setting s have been changed now.
lol FPV
Ragg-e WBX 5"
BUILD
MY CHANNEL
Reply
#6
(15-Feb-2016, 01:39 PM)dronehq Wrote: Hey Oscar your image isn't working, not sure if thats because it was uploaded and the setting s have been changed now.

the images were from Alex's website, but his site is now down so are the images. not much we can do unfortunately.
Don't be a LOS'er, be an FPV'er :) -- Blog - Facebook - Instagram - Twitter - Google Plus
Reply
Login to remove this ad | Register Here
#7
Something I was looking into today. I use Singer oil for my rc car bearings. Has there been any issues with bearing life on motors using Singer oil? I have new motors that I plan to disassemble to clean and lube as I don't really have faith in them being properly cleaned and lubed from the factory.
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Motor Brushless motor winding and rewinding DzikuVx 6 247 14-Dec-2017, 07:51 PM
Last Post: flightmode0
  Tool Workbox - movable mini workshop E.L.K. 1 162 09-Nov-2017, 08:59 PM
Last Post: unseen
  Motor Brushless Motor Care Gr8Stog 5 365 27-Oct-2017, 04:42 PM
Last Post: Gr8Stog
  Tutorial Silverxxx Acro FW flash to H8 mini (Blue Board) Tom BD Bad 11 1,380 14-Jul-2017, 05:27 PM
Last Post: unseen
  Tutorial How to wash your brushless motors Carlos Costa 8 3,478 27-May-2017, 01:57 AM
Last Post: Aaron