Guys, who knows how to configure and wire to SP Racing F3? 

I will appriciate any help.

Hey FLeeX, Not sure if this will help, but found this for you, http://www.helipal.com/storm-bluetooth-m...ng-f3.html

(06-Jun-2016, 03:41 PM)BigglesFPV Wrote: Hey FLeeX, Not sure if this will help, but found this for you, http://www.helipal.com/storm-bluetooth-m...ng-f3.html

I already got this module, even 2 of them : think you wanted to show me how it's wired)) I know now how to wire up but I need to configure it now, saw tons of videos about it but I can't get to AT commands  Thanx for help anyway

Did You try following Painless tutorial?



I had problems with HT-05 too, but I think I had different baud rate pre-set on my module. Ports/baud rate checked?

EDIT: You also may have problems with Arduino software version You are using. I followed Oscar's tip to downgrade to 1.0.5 and it worked in case of my OSD, where newest one didn't connect.

(07-Jun-2016, 09:59 AM)Konrad Stepanajtys Wrote: Did You try following Painless tutorial?



I had problems with HT-05 too, but I think I had different baud rate pre-set on my module. Ports/baud rate checked?

EDIT: You also may have problems with Arduino software version You are using. I followed Oscar's tip to downgrade to 1.0.5 and it worked in case of my OSD, where newest one didn't connect.

Yes I did m8. How to change that baud rate without AT command? I tried to change baud rate at the serial monitor and it didnt help at all and yea I know about the Arduino version, so I tried a newest and that one u mentioned. I can connect it to my mobile phone but I think I need 115000 baud rate to wire it to F3, is it? I need to change baud rate of the module in that serial monitor but I cant get in, it doesnt answer OK to me ))))

P.S. Ports been checked too

(07-Jun-2016, 09:24 AM)FLeeX Wrote: I already got this module, even 2 of them : think you wanted to show me how it's wired)) I know now how to wire up but I need to configure it now, saw tons of videos about it but I can't get to AT commands  Thanx for help anyway

So what is it you wish to do with it?, I thought you only wanted it to connect to cleanflight.

(07-Jun-2016, 10:12 AM)BigglesFPV Wrote: So what is it you wish to do with it?, I thought you only wanted it to connect to cleanflight.

Yea m8 thats what I want to do got 2 of them like I said and one of them will work with my Jiyi P2 Pro FC too

But before I need to program this module to use it on F3 like Painless360 did , need to change baud rate first

I got one more module, I think it's HC-09 or something with BT4.0 and I cant get it work at all lol HC-05 is a bit easier, it connects to my phone but this HC-09 not

---

or may be I need to connect "KEY" pin to somewhere on my FTDI adapter or Nano V3?

---

forgot to say that i dont have button on this modules, so I short circuit where should be a button and it goes to programming mode but it doesnt respond to AT commands

(07-Jun-2016, 10:20 AM)FLeeX Wrote: Yea m8 thats what I want to do got 2 of them like I said and one of them will work with my Jiyi P2 Pro FC too

But before I need to program this module to use it on F3 like Painless360 did , need to change baud rate first

I got one more module, I think it's HC-09 or something with BT4.0 and I cant get it work at all lol HC-05 is a bit easier, it connects to my phone but this HC-09 not

---

or may be I need to connect "KEY" pin to somewhere on my FTDI adapter or Nano V3?

---

forgot to say that i dont have button on this modules, so I short circuit where should be a button and it goes to programming mode but it doesnt respond to AT commands

KEY pin needs to be tied to VCC to put HC-05 into AT mode