Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.
IntoFPV Forum › General Discussion › Mini Quad v
Build Diatone ET200

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Thread Modes
Diatone ET200
Ariel Drach Offline
Forum Beginner
Posts: 2
Threads: 1
Likes Received: 0 in 0 posts
Likes Given: 1
Joined: Jan 2016
Reputation: 0
#1
Exclamation  15-Jan-2016, 04:12 PM (This post was last modified: 15-Jan-2016, 04:17 PM by Ariel Drach.)
Diatone ET200 frame from Diatone Innovations  
This little frame is very nice designed and quick to setup thanks to the integrated PDB.
I would say it's a good FPV cruiser. 

After the first build I have decided to re-design the quad since I notice some weak points mainly in the arms which are supported by only two standoffs and screws .
So I added some customized 3D printed parts which make this quad tougher at the weak points and prettier, well that is my opinion anyway  Tongue

My setup

Frame: Diatone ET200 frame
Motors: Powered by DYS BE1806 2300Kv - Black edition
Esc's: ZTW Spider opto 12A with oneshot
FC: EMAX mini Skyline32 Naze32
Vtx: Dal RC DIY 5.8Ghz 600mw Vtx + Cooling sink 
FPV antennas: FPV 5.8G Gain Petals Clover Mushrooms Antenna TX/RX Set
FPV cam: 600TVL 1/4 1.8mm CMOS FPV 170 Degree Wide Angle Lens
OSD: Micro minimosd
Rx: X8R
Props: Gemfan 5045 ABS CW/CCW Propeller For Mini Quadcopter 250
Batts: Nano tech 3s 1300Mah or can run with 4s setup as well

Customized 3d printed parts: contact me

AUW: 420g

   
   
   
   
   
Reply
Login to remove this ad | Register Here


Possibly Related Threads...
Thread Author Replies Views Last Post
  Diatone c25 mk2 3d print Wolfplay 0 190 16-Aug-2023, 08:08 PM
Last Post: Wolfplay
  Build Hybrid Diatone Roma 5" relentlesstech 7 458 29-Jun-2022, 11:27 PM
Last Post: relentlesstech
  Review Diatone Roma F5 review (6S analog version) L0stB1t 87 24,846 16-Feb-2022, 12:30 AM
Last Post: robegian
  Tutorial Diatone Mamba F722 mini FC - Part 1 ciscoarizona 11 1,432 02-Jun-2021, 10:02 PM
Last Post: rolo95
  Tutorial Diatone Mamba F722 - Part 2 PID Tuning ciscoarizona 1 832 25-May-2021, 02:21 AM
Last Post: the.ronin


Login to remove this ad | Register Here