Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
D4R-II, Naze32, Taranis Telemetry....What am I doing wrong?
#1
Ok so I am trying to get this new fangled telemetry thingy going, and it kind of works. 

Setup:
Naze32 rev5 with Betaflight 2.1.6
D4R-II
Taranis plus with openTX 2.0.19

I am getting signal from naze to radio. Was first running it off of the telemetry port, but then moved it over to pin 6 soft serial, same results on each setup.

Same results on openTX 2.0.19 and 2.1.7.

Here's the issue:
Battery calibration. I will put a fresh battery on and go fly. Life is good. Next battery, it seems as though the telemetry does not reset with battery change out and I have to re-calibrate for the fresh battery. Thoughts? Ideas? I'm a bit stumped.
Reply
Login to remove this ad | Register Here
#2
Hi Scott,
Did you try holding the "Enter button, reset flight" on your Taranis?
Reply
#3
Good to know of this feature, but did not work.
Reply
#4
Hi, what isn't reset? Voltage level? You mean telemetry still stays at the voltage from last battery?
Very odd..
Have you try turning TX off and on?
Don't be a LOS'er, be an FPV'er :)  My Gear - Facebook - Instagram - Twitter
Reply
#5
Yeah the voltage is not resetting. Power cycling the tx doesn't seem to help. Works fine on sensor A1 for the internal rx voltage, but not A2. Watched the youtube videos and combed through the tutorials and set everything up as indicated. FC is reading voltage correctly in cleanflight and low voltage alarm on the quad works. Gonna try setting it up on a different model and see if I can get it to work with that one. Would an external voltage sensor help?
Reply
#6
So it seems to be resetting after I refresh between batteries, however the voltage readout is all off. Looking at information online, it looks like I may have done the math wrong. What is the voltage divideo ratio on naze32?
Reply
#7
Could be different on everyone's ... Adjust it by connecting to a Cleanflight GUI.. You should see flight data on home tab including voltage reading (when your lipo is connected too)

Adjust voltage scale in config tab, and check voltage... Repeat until you get it right?

Remember to remove props!
Don't be a LOS'er, be an FPV'er :)  My Gear - Facebook - Instagram - Twitter
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
Shocked CAUTION: My Zeus5 F411 ES24 FC Came With the Wrong Firmware segler999 0 108 15-Feb-2024, 02:37 AM
Last Post: segler999
  Help Betaflight telemetry output smartport paulno 24 1,132 05-Oct-2023, 06:23 PM
Last Post: SnowLeopardFPV
  Problem with Rush Blade F722 Analog and Telemetry Denethor 7 1,020 10-Dec-2022, 04:37 PM
Last Post: chukaman
  Can flashing the wrong fc firmware damage components Rob Axel 1 920 25-Sep-2022, 10:16 AM
Last Post: SnowLeopardFPV
  Help Aikon F4 + R-XSR SBUS/telemetry ganked 1 272 03-Aug-2022, 07:02 AM
Last Post: ganked


Login to remove this ad | Register Here