Hey! I have a Nazgul5 HD 6S PNP drone with the F722 stack and I recently noticed my custom OSD doesn't show anymore. Custom OSD is turned on in the goggles and is turned on in Betaflight, as well as telemetry being turned on. Can anyone help? Below is some stuff that my guide you! Thanks!


Entering CLI Mode, type 'exit' to return, or 'help'



# diff all

# version
# Betaflight / STM32F7X2 (S7X2) 4.3.2 Nov 28 2022 / 07:30:19 (60c9521) MSP API: 1.44
# config: manufacturer_id: IFRC, board_name: IFLIGHT_BLITZ_F722, version: b0a67988, date: 2022-11-20T06:26:37Z

# start the command batch
batch start

# reset configuration to default settings
defaults nosave

board_name IFLIGHT_BLITZ_F722
manufacturer_id IFRC
mcu_id 000e000a3756500b20383558
signature

# name: Nazgul5 HD

# feature
feature -RX_PARALLEL_PWM
feature LED_STRIP

# serial
serial 0 1 115200 57600 0 115200

# led
led 0 0,0::L:0
led 1 1,0::L:0
led 2 2,0::L:0
led 3 3,0::L:0

# aux
aux 0 0 0 1700 2100 0 0
aux 1 1 1 900 2100 0 0

# vtxtable
vtxtable bands 5
vtxtable channels 8
vtxtable band 1 BOSCAM_A A CUSTOM  5865 5845 5825 5805 5785 5765 5745 5725
vtxtable band 2 BOSCAM_B B CUSTOM  5733 5752 5771 5790 5809 5828 5847 5866
vtxtable band 3 BOSCAM_E E CUSTOM  5705 5685 5665    0 5885 5905    0    0
vtxtable band 4 FATSHARK F CUSTOM  5740 5760 5780 5800 5820 5840 5860 5880
vtxtable band 5 RACEBAND R CUSTOM  5658 5695 5732 5769 5806 5843 5880 5917
vtxtable powerlevels 4
vtxtable powervalues 25 100 400 800
vtxtable powerlabels 25 100 400 800

# master
set dyn_notch_q = 120
set dyn_notch_max_hz = 500
set acc_calibration = -28,9,29,1
set mag_hardware = NONE
set baro_hardware = NONE
set dshot_burst = AUTO
set motor_pwm_protocol = DSHOT600
set failsafe_delay = 4
set failsafe_recovery_delay = 20
set vbat_max_cell_voltage = 422
set yaw_motors_reversed = ON
set small_angle = 180
set frsky_unit = IMPERIAL
set osd_warn_core_temp = OFF
set osd_rssi_pos = 314
set osd_link_quality_pos = 310
set osd_rssi_dbm_pos = 299
set osd_tim_2_pos = 405
set osd_flymode_pos = 2509
set osd_vtx_channel_pos = 373
set osd_current_pos = 2401
set osd_mah_drawn_pos = 2432
set osd_craft_name_pos = 2541
set osd_gps_speed_pos = 342
set osd_gps_sats_pos = 310
set osd_home_dir_pos = 302
set osd_home_dist_pos = 430
set osd_altitude_pos = 341
set osd_warnings_pos = 14764
set osd_avg_cell_voltage_pos = 2369
set osd_battery_usage_pos = 35233
set osd_disarmed_pos = 2336
set debug_mode = GYRO_SCALED
set vtx_band = 5
set vtx_channel = 3
set vtx_power = 1
set vtx_freq = 5732
set name = Nazgul5 HD

profile 0

# profile 0
set iterm_windup = 100
set yaw_lowpass_hz = 70
set p_pitch = 55
set i_pitch = 90
set d_pitch = 41
set f_pitch = 124
set p_roll = 50
set i_roll = 85
set d_roll = 38
set f_roll = 117
set p_yaw = 54
set i_yaw = 90
set f_yaw = 117
set d_min_roll = 23
set d_min_pitch = 25

profile 1

profile 2

# restore original profile selection
profile 0

rateprofile 0

# rateprofile 0
set roll_rc_rate = 19
set pitch_rc_rate = 19
set yaw_rc_rate = 19
set roll_expo = 60
set pitch_expo = 60
set yaw_expo = 60
set roll_srate = 90
set pitch_srate = 90
set yaw_srate = 90

rateprofile 1

rateprofile 2

rateprofile 3

rateprofile 4

rateprofile 5

# restore original rateprofile selection
rateprofile 0

# save configuration
save

Try to reload font or change font.