Hello guest, if you read this it means you are not registered. Click here to register in a few simple steps, you will enjoy all features of our Forum.
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.
IntoFPV Forum › Hardware Discussion › Motor, ESC and Prop v
6” prop motor suggestions

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Thread Modes
6” prop motor suggestions
Rob3ddd Offline
Member
*
Posting Freak
Posts: 1,843
Threads: 203
Likes Received: 346 in 264 posts
Likes Given: 306
Joined: May 2020
Reputation: 11
#1
02-Oct-2020, 07:10 PM
I’m going to get BangGod 6” frame and I’d like to use 6” 2 bladed props and I’ll try tri-Blade’s too.
 
   Motor selection I’m not sure and I’m wanting efficiency not speed.
  I may go 4-5S.
   Any suggestions?
 I found a red cannon ball V2 2406 2020 or 2330kv but reviews are limited.
Reply
Login to remove this ad | Register Here
Rob3ddd Offline
Member
*
Posting Freak
Posts: 1,843
Threads: 203
Likes Received: 346 in 264 posts
Likes Given: 306
Joined: May 2020
Reputation: 11
#2
02-Oct-2020, 07:24 PM
Brother avenger 2507 should be highly efficient and good for 6-7” props.
1500 or 1850kv .
I’ll check out performance chart .
[-] The following 1 user Likes Rob3ddd's post:
  • wllmlutz
Reply
wllmlutz Offline
BlutzkriegFPV
*
Crash Expert Quad Builder
Posts: 788
Threads: 47
Likes Received: 543 in 341 posts
Likes Given: 820
Joined: Apr 2020
Reputation: 7
#3
03-Oct-2020, 12:13 AM
(02-Oct-2020, 07:24 PM)Rob3ddd Wrote: Brother avenger 2507 should be highly efficient and good for 6-7” props.
1500 or 1850kv .
 I’ll check out performance chart .

I run these motors on my 7" BangGod and they have no problems at all. Very good motors!
Website
Reply
Rob3ddd Offline
Member
*
Posting Freak
Posts: 1,843
Threads: 203
Likes Received: 346 in 264 posts
Likes Given: 306
Joined: May 2020
Reputation: 11
#4
03-Oct-2020, 01:52 AM (This post was last modified: 03-Oct-2020, 01:54 AM by Rob3ddd.)
(03-Oct-2020, 12:13 AM)wllmlutz Wrote: I run these motors on my 7" BangGod and they have no problems at all. Very good motors!

  I’m very tempted to get the 7” instead and still might.
  I seen your punisher and it looks like it’s dialed in and flying on rails.
   I’ll look at your setup on your thread.Nice build!
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Solved 35mm Bi-Blade Prop 1mm Shaft brettbrandon 10 286 17-May-2024, 03:12 AM
Last Post: brettbrandon
Question Help Diatone MXC Taycon Cinewhoop's 4th motor isn't working rr240 2 189 28-Apr-2024, 02:58 PM
Last Post: Pathfinder075
Question Help Diatone MXC Taycon Cinewhoop's 4th motor isn't working rr240 0 116 23-Apr-2024, 09:36 PM
Last Post: rr240
  Sometimes a motor surprises you - in a good way mstc 20 934 10-Apr-2024, 09:00 PM
Last Post: mstc
  Help Brother Hobby Motor VY1507 hawk01 3 178 05-Apr-2024, 07:58 AM
Last Post: hugnosed_bat


Login to remove this ad | Register Here