Welcome, Guest | You have to register before you can post on our site. | Forum Statistics | » Members: 17,310 » Latest member: k2bow » Forum threads: 22,785 » Forum posts: 207,167
Full Statistics | Online Users | There are currently 181 online users. » 0 Member(s) | 176 Guest(s) Applebot, Bing, Google, Internet Archive, Yandex | | | Bluejay not working on G-H-30 ESCs, but it SHOULD | Posted by: Helmut585 - 28-Jan-2023, 12:17 PM - Forum: BLHeli_S & BLHeli_32 - Replies (6) | | Hi, I have a Flywoo Explorer that I use to get video footage. Unfortunately, it flies kind of bumpy and not as long as other people report it to. I got to know that other people got their Explorer shipped with Bluejay ESC firmware and it flies even better when on 95PWM, according to them. Here is a source video. They have the DJI O3 version, but the same ESC (I checked). I have the analog version. I can flash Bluejay to my ESC that otherwise runs BLHeli_S, so it would be nice to have RPM filtering. However, when I flash Bluejay, I do not get the last ESC beeps and the quad will not arm. Not on 24, 48 or 96 PWM, also not when turning up the starting power in Bluejay. I even got a screenshot from the guys ESC configuration and applied the same (standard) settings,but it doesn't work. Is there perhaps something in Betaflight I have to change? Can you guys think of another reason why Bluejay does not work for me? I tried to solve this for over a week now and am kind of deperate. Any advice is highly appreciated. ? | | | Issues Installing ELRS Reciever | Posted by: NyxOTNC - 28-Jan-2023, 07:52 AM - Forum: Beginner Questions - Replies (13) | | Hello everyone, I am newer to the world of FPV and have recently purchased my first non-commercial FPV drone, a Venom H20 HD from Flywoo. Now for various reasons I ended up with a version that did not ship with a reciever (I had a deal for a v1 DJI controller but it fell through) and have decided to add my own ELRS reciever, so I purchased a Radiomaster RP1 and a matching Zorro TX, which I am very happy with. I have sucessfully soldered the reciever to the existing reciever wiring on the drone (I had it checked by an actual avionics specialist) and the reciever works. I've flashed the latest ELRS firmware onto both the TX and the RX and installed the necessary .lua scripts on the TX as well, and they pair up right away with eachother. The problem is the TX is not being recognized by the drone in Betaflight, so I'm going to assume that the RX and the FC are not communicating with eachother properly. The FC is a Goku Hex F411 and as such I checked the box in the ELRS configurator to invert the CRSF signal to allow it to communicate with the SBUS only FC, and also verified that the UART which is set to serial in BetaFlight matches the physical one on the FC. The problem I'm having is that I don't know if Flywoo did anything during the setup of this drone (because even though they ship a version with a CRSF reciever, this one was intended to use the built in DJI reciever in the Caddx Vista) that's causing me a problem, and since I don't yet know what exactly I don't know, I can't even Google an answer. If anyone has some insight I would be very greatful. | | | BEC for DJI O3 unit | Posted by: peek2much2 - 27-Jan-2023, 02:56 PM - Forum: General Topics - Replies (3) | | Guys, would you say this BEC is good to use to hook up my O3 to my FC? I want to avoid going directly to VBat just in case some spike or something happens and fries my stuff. MICRO BEC MATEK 6-30V TO 5V/9V-ADJ (6S) * High Efficiency Synchronous Step-down regulator * Wide 6V to 30V Operating Input Range * Continuous load current: 1.5 Amps (Max.2.5A 5s/minute) * VOut 5V or 9V Adj. Default is 5V. * VOut Load Regulation: 2% * Standby current: <5mA Else, what would you all recommend or have done that's proven in regards to the O3 unit? | | | No input in velocidrone | Posted by: Yelreppa - 27-Jan-2023, 09:57 AM - Forum: FPV Simulators - No Replies | | Always had no issues with velocidrone stick inputs but now don't get anything!? Using a Radio king tx and normal usb cable,have also deleted and reinstalled in it and still no look. Need to keep practicing asam now really rusty | | | Eachine | Posted by: Dak_4008 - 27-Jan-2023, 03:46 AM - Forum: General Topics - Replies (7) | | Hey Guys I was just having a shower thought and thinking if eachine was gonna come out with a Dji bnf/rtf. I think that would be great but the competition is rotor riot, getfpv bundles and so on. What’s y’all’s opinion? i think they should. | | | |